ASME SA 234 Grade WPB Carbon Steel Seamless Pipes

ASME SA 234 Grade WPB Specification

ASME SA 234 Grade WPB Carbon Steel Seamless Pipes are Medium Carbon Steel Pipes with max 0.30 % carbon content with combination of 0.29 – 1.06 % manganese. These Pipes are most commonly used for general purpose applications worldwide. ASME SA 234 Grade WPB Pipes are ductile and strong Pipes with long wearing properties. These Pipes are manufactured as per ASME Specification and commercially referred as carbon steel Pipes.

ASME SA 234 Grade WPB Properties

[sociallocker]

Chemical Properties
Carbon Silicon Manganese Phosphorous Sulphur Molybdenum Nickel Chromium Copper Others
max 0.30 min 0.10 0.29 – 1.06 0.035 0.035 max 0.15 max 0.40 max 0.40 max 0.40 V min 0.08


Mechanical Properties
Yield Strength Tensile Strength Elongation A5 min
MPa min ksi min MPa min MPa min ksi min Percentage
415 585 60 30

Equivalent Designation
DIN EN BS NFA ASTM ASME
EN P265GH Grade 10216-2 ASTM A234 WPB ASME SA 234 WPB

[/sociallocker]

  • Carbon Steel
  • Alloy Steel
  • Low Temperature Carbon Steel
  • High Temperature Carbon Steel
  • Low Temperature Alloy Steel
  • High Temperature Alloy Steel

Types of ASME SA 234 Grade WPB Carbon Steel Seamless Pipes

Pipes

Seamless Pipes

  • Cold Drawn Seamless Pipes
  • Hot Drawn Seamless Pipes

Welded Pipes

  • Electric Resistance Welded(ERW) Pipes
  • Continous Welded(CW) Pipes
  • Submerged Arc Welded(SAW) Pipes
  • Double Submerged Arc Welded(DSAW) Pipes
  • Spiral Welded Pipes
  • High Frequency Induction(HFI)
  • Longitudinally Submerged Arc Welded(LSAW) Pipes

Tubes

Seamless Tubes

  • Cold Drawn Seamless Tubes
  • Hot Drawn Seamless Tubes

Welded Tubes

  • Electric Resistance Welded(ERW) Tubes
  • Continous Welded(CW) Tubes
  • Submerged Arc Welded(SAW) Tubes
  • Double Submerged Arc Welded(DSAW) Tubes
  • Spiral Welded Tubes
  • High Frequency Induction(HFI)
  • Longitudinally Submerged Arc Welded(LSAW) Tubes

Hollow Sections

Pipes

  • Boom Pipe
  • Culvert Pipes
  • Square Pipes
  • Round Pipes
  • Honed Pipes

Tubes

  • Boom Tubes
  • Culvert Tubes
  • Square Tubes
  • Round Tubes
  • Honed Tubes

Delivery Executions of ASME SA 234 Grade WPB Carbon Steel Seamless Pipes

Tube Ends

All tubes are supplied with clean, square cut ends.Deburring and/or chamfering can be carried out on request.

Tube surface

Tubes are supplied normally without anti-corrosive treatment, but anti-corrosive treatment is available and is carried out on request.

Protection

  • Black and Bare
  • External Varnished with Black or Clear LAcquer

Mill test certificate

  • MTC is issued in accordance with EN 10204.

Packaging

ASME SA 234 Grade WPB Carbon Steel Seamless Pipes are bundled as standard, with steel straps into hexagonal bundles with one end flush.Length sorting can be carried out on request. Tubes can also be bundled in multiples. Bundle weights are adjusted as requested by the customer. Each bundle contains tubes from a single cast/heat only.

Marking

ASME SA 234 Grade WPB Carbon Steel Seamless Pipes is marked with tube type, heat number, steel grade and size. Information is repeated along the whole length of the tube. Other markings, such as stamping, can be made on request. Bundles are also labeled with a tag having info both alphanumeric and by bar code.

Labelling

ASME SA 234 Grade WPB Carbon Steel Seamless Pipes delivered direct from our mill is labeled in accordance with automotive standard, ie with both alphanumeric and bar code information. Customer specific data can be added on request.

[psp_rs_product name=”ASME SA 234 Grade WPB Carbon Steel Seamless Pipes” url=”http://www.ferropipe.com/asme-sa-234-grade-wpb-carbon-steel-seamless-pipes” image=”http://www.ferropipe.com/wp-content/uploads/material/asme-sa-234-grade-wpb-carbon-steel-seamless-pipes.jpg” description=”ASME SA 234 Grade WPB Carbon Steel Seamless Pipes are used for high temperature service.SA 234 Gr.WPB Pipes are provided in hot dip galvanised and black conditions” brand=”FerroPipE” manufacturer=”MSL, ISMT, JSL, JINDAL, TATA STEEL, BHUSHAN STEEL, SUMITOMO, TENARIS” model=”Carbon Steel Pipes” best_rating=”4″ worst_rating=”3″ current_rating=”4″ avg_rating=”3″ nb_reviews=”114″ condition=”New” availability=”InStock”]

Dimensional Standards of ASME SA 234 Grade WPB Carbon Steel Seamless Pipes

FEDERAL

WWP-404c is similar to ASTM A-53 except that Government inspection and continuous identification marking of electric weld and seamless is mandatory. It covers black and galvanized welded and seamless pipe for flanging, bending, and coiling and for use with fresh water, oil, steam, air, and gas on shore plus a limited number of shipboard uses. Sizes 1/8 inch through 24 inch.WWP-406c is a federal specification comparable to ASTM A-120 (withdrawn 1988). Mills can certify that A-120 pipe in a distributor-s stock meets all the requirements of WWP-406c.

A.W.W.A.

C-200 covers black welded and seamless pipe intended for the conveyance of water in sizes 6 inch and larger. Specification prescribes hydrostatic test pressures for sizes of pipe covered. Tensile, flattening, and bending tests are required.

ASME

  • B31.1 Code for pressure piping.plants, and industrial plants.
  • B31.2 Fuel Gas Piping.
  • B31.3 Petroleum Refinery Piping.
  • B31.4 Liquid PetroleumTransportation Piping Systems.
  • B31.5 Refrigeration Piping.
  • B31.7 Nuclear Power Piping
  • B31.8 GasTransmission and Distributing Piping Systems. Covers design, fabrication, installation, inspection, testing, and the safety aspects of operation and maintenance of gas transmission and distribution systems.

ANSI (ASME)

  • B36.10 American Standard for Wrought-Steel and Wrought-Iron pipe. Designates dimensions, weights, and schedule numbers for welded and seamless pipe. Schedules 10 through Schedules Double Extra Heavy (DXH/XXH).
  • B36.19 American Standard for Stainless Steel Pipe. Designates dimensions, weights, and schedule numbers for welded and seamless Stainless Steel Pipe, Schedules 5 through Schedules 80.

A.A.R.

  • M-111 covers black and galvanized welded and seamless pipe intended for coiling, bending, flanging, and other special purposes and is suitable for welding. Purpose for which pipe is intended should be stated on orders. M-111 is comparable in most requirements to ASTM A-53.
  • M-130 covers black and galvanized welded and seamless pipe for ordinary uses in steam, water, gas, and air lines. Sizes 1/8 inch through 12 inch. Pipe to this specification is not intended for close coiling, bending, or high temperature service. M-130 is comparable in most requirements to ASTM A-120.

ASME SA 234 Grade WPB specification covers seamless and electric resistance-welded steel pipe used as conduit for the installation of high-pressure pipe-type electrical cables in NPS 4 to NPS 12.Recommended pipe size will be developed by FerroPipe upon receipt of your inquiry. A print or sketch of the part to be produced should be included. Grade, chemical analysis and surface condition are carefully considered, and production processes are tailored to achieve the best tubing for the end use.

FerroPipE is considered as the most Reliable ASME SA 234 Grade WPB Pipes Supplier from India.

ASME SA 234 Grade WPB Carbon Steel Seamless Pipes stockist in Mumbai, India.Ferropipe stocks a complete range of IBR Certified ASME SA 234 Grade WPB Carbon Steel Seamless Pipes in outer diameter tube sizes ½”-24” and Nominal bore NB sizes 15NB-600NB in Mumbai, India. Exporting Carbon Steel Pipes and Alloy Steel Pipes to countries worldwide including IRAN, IRAQ, KUWAIT, QATAR, South Africa, Nigeria, Saudi Arabia, Australia, Canada & Mexico.

In addition to the marking specified in Specification A 999/A 999M, the marking should have the length, an additional symbol -S-, if ASME SA 234 Grade WPB Carbon Steel Seamless Pipes conforms to any of the Supplementary Requirements S1 to S6, the schedule number of the pipe is ordered to a schedule number viz. SCH 5,10,20,30,40,60,80,100,120,140,160,XS, XXS, STD, and the heat number of or manufacturer-s number by which the heat can be identified as per ASME SA 234 Grade WPB.

Wall Thickness : the minimum wall thickness at any point or end on ASME SA 234 pipes and tubes shall not be greater than 12.5% under the nominal thickness specified.
Inner Diameter: For pipe ordered in inside diameter, the inside diameter shall not vary more than ñ 1% from the required/specified inside diameter.

The Manufacturer shall provide Material Test certificate of inspection to the purchaser stating that the material has been manufactured, sampled, tested, and inspected in accordance with ASME SA 234 Grade WPB( including year of issue), and has satisfied all the requirements of ASME SA 234.

Pipes and Tubes manufactured as per ASME SA 234 Grade WPB are certified with En 10204 Type 3.1/3.2. IBR,NACE,HIC,IGC,IMPACT are adhered as supplementary testing requirements.

Leave Comment

Your email address will not be published.

You may use these HTML tags and attributes: <a href="" title=""> <abbr title=""> <acronym title=""> <b> <blockquote cite=""> <cite> <code> <del datetime=""> <em> <i> <q cite=""> <s> <strike> <strong>

clear formSubmit