EN 10083-2 Grade 28Mn6 Carbon Steel Seamless Pipes and Tubes

EN 10083-2 Grade 28Mn6 Specification

EN 10083-2 Grade 28Mn6 Carbon Steel Seamless Pipes and Tubes are most commonly used for general purpose applications worldwide.EN 10083-2 Grade 28Mn6 Pipes and Tubes are ductile and strong Pipes and Tubes with long wearing properties .These Pipes and Tubes are manufactured as per EN Specification and commercially referred as carbon steel Pipes and Tubes.

EN 10083-2 Grade 28Mn6 Properties

[sociallocker]

Chemical Properties
Carbon Silicon Manganese Phosphorous Sulphur Molybdenum Nickel Chromium Copper Others
0.25-0.32 max 0.40 1.30-1.65 0.03 0.035 max 0.10 max 0.40 max 0.40


Mechanical Properties
Yield Strength Tensile Strength Elongation A5 min
MPa min ksi min MPa min MPa min ksi min Percentage

Equivalent Designation
DIN EN BS NFA ASTM ASME
DIN 17204 Grade 28Mn6 EN 10083-2 Grade 28Mn6 ASTM SAE Grade 1527

[/sociallocker]

  • Carbon Steel
  • Alloy Steel
  • Low Temperature Carbon Steel
  • High Temperature Carbon Steel
  • Low Temperature Alloy Steel
  • High Temperature Alloy Steel

Types of EN 10083-2 Grade 28Mn6

Pipes

Seamless Pipes

  • Cold Drawn Seamless Pipes
  • Hot Drawn Seamless Pipes

Welded Pipes

  • Electric Resistance Welded(ERW) Pipes
  • Continous Welded(CW) Pipes
  • Submerged Arc Welded(SAW) Pipes
  • Double Submerged Arc Welded(DSAW) Pipes
  • Spiral Welded Pipes
  • High Frequency Induction(HFI)
  • Longitudinally Submerged Arc Welded(LSAW) Pipes

Tubes

Seamless Tubes

  • Cold Drawn Seamless Tubes
  • Hot Drawn Seamless Tubes

Welded Tubes

  • Electric Resistance Welded(ERW) Tubes
  • Continous Welded(CW) Tubes
  • Submerged Arc Welded(SAW) Tubes
  • Double Submerged Arc Welded(DSAW) Tubes
  • Spiral Welded Tubes
  • High Frequency Induction(HFI)
  • Longitudinally Submerged Arc Welded(LSAW) Tubes

Hollow Sections

Pipes

  • Boom Pipe
  • Culvert Pipes
  • Square Pipes
  • Round Pipes
  • Honed Pipes

Tubes

  • Boom Tubes
  • Culvert Tubes
  • Square Tubes
  • Round Tubes
  • Honed Tubes

Dimensional Tolerances of EN 10083-2 Grade 28Mn6

OD/Wall tolerance

Outer diameter and wall Thickness
Execution Size Range OD Tolerance Wall tolerance
Hot-rolled Tube OD – 80 mmOD > 80 mmWall < 12 mmWall - 12 mm ± 0.4 mm± 0.5 % of OD ± 0.7 mm± (5 % x wallthickness + 0.1 mm
Hot-rolled peeled tube All sizesWall < 12 mmWall - 12 mm + 0.25/- 0 mm ± 0.8 mm± (5 % x wall thickness+ 0.2 mm)
Cold Worked tubecold-rolled or cold-drawn OD < 40 mmOD 40 - 80 mmOD > 80 Wall Thickness< 6 mm Wall Thickness6 - 8 mm Wall Thickness > 8 + 0.30/- 0 mm*+ 0.35/- 0 mm*+ 0.40/- 0 mm* ± 0.30 mm± 0.35 mm± 0.40 mm

Straightness

The maximum deviation from the straight line is 1 mm on a gauge length of 1000 mm.

Ovality

The maximum out-of-roundness is 65% of the total outer diameter tolerance.

Standard length tolerances

Component length (mm) OD 30-100 mm OD 100-254 mm
10-100 + 1.0/- 0 + 2.0/- 0
100-600 + 2.0/- 0 + 3.0/- 0
600-1200 + 3.0/- 0 + 4.0/- 0
1200-5000 + 5.0/- 0 + 6.0/- 0

Delivery Executions of EN 10083-2 Grade 28Mn6

Tube Ends

All tubes are supplied with clean, square cut ends.Deburring and/or chamfering can be carried out on request.

Tube surface

Tubes are supplied normally without anti-corrosive treatment, but anti-corrosive treatment is available and is carried out on request.

Protection

  • Black and Bare
  • External Varnished with Black or Clear LAcquer

Mill test certificate

  • MTC is issued in accordance with EN 10204.

Packaging

Tubes are bundled as standard, with steel straps into hexagonal bundles with one end flush.Length sorting can be carried out on request. Tubes can also be bundled in multiples. Bundle weights are adjusted as requested by the customer. Each bundle contains tubes from a single cast/heat only.

Marking

Each tube is marked with tube type, heat number, steel grade and size. Information is repeated along the whole length of the tube. Other markings, such as stamping, can be made on request. Bundles are also labeled with a tag having info both alphanumeric and by bar code.

Labelling

Material delivered direct from our mill is labeled in accordance with automotive standard, ie with both alphanumeric and bar code information. Customer specific data can be added on request.

[psp_rs_product name=”EN 10083-2 Grade 28Mn6 Carbon Steel Seamless Pipes and Tubes” url=”http://www.ferropipe.com/en-10083-2-grade-28mn6-carbon-steel-seamless-pipes-and-tubes” image=”http://www.ferropipe.com/wp-content/uploads/material/en-10083-2-grade-28mn6-carbon-steel-seamless-pipes-and-tubes.jpg” description=”EN 10083-2 Grade 28Mn6 Carbon Steel Seamless Pipes and Tubes are EN specification Pipes and Tubes used for structural applications.Ferropipe is a well known stockist of EN 10083-2 Pipes and Tubes In Mumbai/India” brand=”FerroPipE” manufacturer=”MSL, ISMT, JSL, JINDAL, TATA STEEL, BHUSHAN STEEL, SUMITOMO, TENARIS” model=”Carbon Steel Pipes and Tubes” best_rating=”5″ worst_rating=”4″ current_rating=”4″ avg_rating=”5″ nb_reviews=”165″ condition=”New” availability=”InStock”]

Dimensional Standards of EN 10083-2 Grade 28Mn6

FEDERAL

WWP-404c is similar to ASTM A-53 except that Government inspection and continuous identification marking of electric weld and seamless is mandatory. It covers black and galvanized welded and seamless pipe for flanging, bending, and coiling and for use with fresh water, oil, steam, air, and gas on shore plus a limited number of shipboard uses. Sizes 1/8 inch through 24 inch.WWP-406c is a federal specification comparable to ASTM A-120 (withdrawn 1988). Mills can certify that A-120 pipe in a distributor-s stock meets all the requirements of WWP-406c.

A.W.W.A.

C-200 covers black welded and seamless pipe intended for the conveyance of water in sizes 6 inch and larger. Specification prescribes hydrostatic test pressures for sizes of pipe covered. Tensile, flattening, and bending tests are required.

ASME

  • B31.1 Code for pressure piping.plants, and industrial plants.
  • B31.2 Fuel Gas Piping.
  • B31.3 Petroleum Refinery Piping.
  • B31.4 Liquid PetroleumTransportation Piping Systems.
  • B31.5 Refrigeration Piping.
  • B31.7 Nuclear Power Piping
  • B31.8 GasTransmission and Distributing Piping Systems. Covers design, fabrication, installation, inspection, testing, and the safety aspects of operation and maintenance of gas transmission and distribution systems.

ANSI (ASME)

  • B36.10 American Standard for Wrought-Steel and Wrought-Iron pipe. Designates dimensions, weights, and schedule numbers for welded and seamless pipe. Schedules 10 through Schedules Double Extra Heavy (DXH/XXH).
  • B36.19 American Standard for Stainless Steel Pipe. Designates dimensions, weights, and schedule numbers for welded and seamless Stainless Steel Pipe, Schedules 5 through Schedules 80.

A.A.R.

  • M-111 covers black and galvanized welded and seamless pipe intended for coiling, bending, flanging, and other special purposes and is suitable for welding. Purpose for which pipe is intended should be stated on orders. M-111 is comparable in most requirements to ASTM A-53.
  • M-130 covers black and galvanized welded and seamless pipe for ordinary uses in steam, water, gas, and air lines. Sizes 1/8 inch through 12 inch. Pipe to this specification is not intended for close coiling, bending, or high temperature service. M-130 is comparable in most requirements to ASTM A-120.

EN 10083-2 Grade 28Mn6 European standard covers quenching and tempering And Technical delivery conditions for non alloy steels. Pipe will be supplied in 5-7 metre random lengths with butt-weld ends and varnished to avoid oxidation of the steel when in storage. All pipes are fully certified and traceable with heat numbers hard stamped onto each random length. Ferro Pipe can supply cut lengths; long pieces and even bore from forged, machined bar to satisfy your urgent demand.

FerroPipE is considered as the most Reliable EN 10083-2 Grade 28Mn6 Pipes and Tubes Supplier from India.

EN 10083-2 Grade 28Mn6 Carbon Steel Seamless Pipes and Tubes are certified with Mill test Certificate in accordance with En 10204 Type 3.1/3.2. Where 3.2 indicates In-stage inspection by independent inspection agencies like TUV, DNV, BVQS, LLOYDS & EIL.
IBR, NACE MR 0175,NACE MR 0103, HIC, IGC, IMPACT are adhered as supplementary testing requirements for EN 10083-2 Grade 28Mn6 which can be fulfilled with a government approved NABL laboratory.
EN 10083-2 Grade 28Mn6 Pipes and Tubes are supplied in varnished condition in order to prevent formation of rust.
EN 10083-2 Grade 28Mn6 Pipes and Tubes are used mainly for automobile sectors, interior & exterior architectural structures, water pipe lines, Gas lines, Oil & Gas industries etc.
Little known ways to understand 140 different Types of EN Specification Pipes
Leave Comment

Your email address will not be published.

You may use these HTML tags and attributes: <a href="" title=""> <abbr title=""> <acronym title=""> <b> <blockquote cite=""> <cite> <code> <del datetime=""> <em> <i> <q cite=""> <s> <strike> <strong>

clear formSubmit